By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
What are your thoughts on How to Install a Bathtub Yourself?
Mounting a bathtub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably hard job. If the old bathtub is readily easily accessible, the task can move easily; if you have to open a wall surface to eliminate the old bathtub and also position the new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to leave the old tub and set in the new one. Make sure you have qualified on your own for the job and are comfortable attempting it. As opposed to employing a specialist to take control of a halfway-completed task, it is much better to think about using one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This article will aid you set up a new bath tub in your restroom if you have actually currently purchased a new bathtub and don't require to alter the arrangement of your previous water pipes.
Your devices and also product checklist ought to make up the following:
Planning for the Installation
First of all, the sustaining framework provided with the bathroom ought to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be rather problematic due to the limited access that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning during this process. When the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Making use of both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are helpful in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub till the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Switch on the water supply and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow outlet and the normal electrical outlet for leakages.
Finally, take care of the bath paneling as described in the supplier's user's manual. Tiling and securing around the bath tub should wait till the bath tub has been made use of at the very least when as this will settle it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines remain in location in between the tap and the sink. Secure the faucet in position with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, creating the water to pass through the wall surface in between the bathroom and the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can fracture fairly very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the market. It is recommended to fit the tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very taken with Tools You Need to Install a New Bathtub and I hope you enjoyed the blog post. Are you aware of somebody else who is very much interested in the subject? Be sure promote it. Many thanks for your time invested reading it.
Need help? Call. Report this page